• Ge Front Load Dryer Manual
• Ge Front Load Gas Dryer

Sears International Online ShoppingIf you are planning to visit the United States, or have friends and family here, shop at Sears to get everything you want—including gifts for yourself or others. Shopping online in the U.S. At Sears could not be easier. You can pay for your order in a store or even use an international credit card. Once you place an order, you (or someone you know) can pick it up at a Sears store, have it shipped to over 100 countries—whatever is most convenient for you. If you are looking to do some international online shopping, be sure to visit.

This is a drum bearing slide, also known as bearing drum slide, glide, or pad, that is fitted to a dryer. The slide supports the front drum as the drum rotates.

Check both slides for signs of wear, because they often wear at the same rate, and should be replaced at the same time; there are 2 slides per dryer. The drum bearing slide may need to be replaced if the dryer is not tumbling, takes longer than usual to dry clothes, or is noisy during use. This is a white plastic part that is sourced directly from the manufacturer. Sold individually. The drum slides support the front of the dryer drum. As they start to break down it may cause your dryer to make noise or not dry clothes in the usual amount of time. You will need to purchase two for both sides of your dryer.

They attach to the outer-most sides of the bearing. The manufacturer recommends replacing both slides at the same time. Take this opportunity to clean out the lint and dust in the dryer, to keep it running smoothly. This is a genuine replacement part that comes directly from the manufacturer. This item is sold individually. This is a dryer drum drive belt.

It is 89.5 inches long with four ribs on the inside for a better grip. The drive belt on your dryer attaches to the motor pulley and then wraps around the drum and a tensioner pulley, and spins the drum as the motor rotates. Your dryer drum cannot spin without this belt. Belts can stretch or become brittle over time which may cause it to malfunction. This is an original manufacturer replacement part. Be sure to use work gloves to protect your hands from sharp internal parts during this repair. This is a duct felt seal for a dryer.

Ge Front Load Dryer Manual

The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised.

Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer.

This front drum bearing helps your dryer operate as quietly as possible. This is an OEM part and is sold individually.

It is about 10 inches in height and 22 inches in width. It is made entirely out of plastic and is white in color. If your dryer model has a light in it, remove the light bulb before removing the bearing because it will hit the bulb and potentially shatter it. Please note that although the slides are not included in this part, the drum slides should also be replaced when replacing this bearing. This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the timer will not advance, or the dryer shuts off too soon, the issue may be the control knob itself. This clip is sold individually.

Although this part fits with some different brands, be sure to check the list of brands below to make sure it fits with your dryer unit. Refer to the manual provided by the manufacturer for further installation instructions. This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions.

The bearing plate comes with a slot in it for the ground strap. Spider man 2000 video game pc free download. This part helps keep your dryer running as smoothly as possible with as little noise as possible by supporting the back of the dryer drum and reducing friction as the drum rotates. Over time, your drum bearing will wear out, cause your dryer to be noisy, and you will have to replace it. There may be some sharp internal parts, so be sure to wear work gloves during repair.

This is a lint filter screen that is used for many dryers. It has a metal screen with a white plastic frame, and is approximately 13 inches wide. This part is sold individually. The lint filter traps lint while clothes are being dried and prevents the lint from building up in clothes and internal parts of your appliance. Neglecting to clean your filter on a regular basis can negatively affect the operation of your dryer and is also a fire hazard. Be sure to clean your filter on a regular basis. Installation is easy, simply slide the filter in and out of the filter slot.

This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on the door strike, and will not stay closed, you may need to replace the door latch. This part is square in shape, and is approximately 3/4-inch in length, by 3/4-inch in width. The part is made of white plastic with a metal tab. To access the door latch, you will need to remove the top and side panels on your dryer.

To complete this repair, simply pop the damaged door latch out of position, and snap the new one into place. The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open.

This is a part for your dryer. The interlock switch senses the door is shut and the dryer can begin.

Ge Front Load Gas Dryer

This part might need to be replaced if your dryer is not starting or is in process while the door is open. The black rectangular part of the switch is approximately 2 inches long and a 1/2-inch wide with two gold plates on either end. This is a genuine OEM part that is sourced right from the manufacturer.